CAJ Innovations Forums

Here is the map from my bike. The bike is stock and has an LC1 lambda sensor. It runs closed loop.
This map is a result of many autotune rides and also logging for later analysis.

Many users receive this as their starting pointing.

https://cajinnovations.com/yabb0/YaBB.pl?action=downloadfile;file=Sport.ecu (11 KB | 996 )

Thx.

Always wondered why there is no CylOffs mapping in your maps,
is there really no need f that?!?
You have one or 2 Lambdas?

There's normally no reason for a Guzzi to have different characteristics between left and right cylinder, as they get equal cooling and have (damn near) identical exhausts lengths and so on.

A Ducati will have much worse cooling for the rear cylinder, and if that is mitigated with water cooling it still applies for the exhaust temperatures (quicker cooling in the exhaust pipe affects back pressure and will affect the tune, academically or not). Also, a Ducati will never have identical exhausts. Even if the lengths are equal due to some extra bends on the rear one, they are still not the same.

My stock WM ECU do have some offsets though. There's no pattern - some are plus, some are minus. I don't regard them as being of any value.

Code:

Delta (ms)
1000 1200 1350 1500 1800 2100 2400 2700 3000 3500 4000 4500 5000 6000 7500 8000
79 0.13 0.09 0.06 0.63 0.63 0.66 0.50 0.22 0.69 0.28 0.41 0.13 0.13 -0.3 -0.1 0.06
60 0.00 0.00 0.00 0.44 0.53 0.63 0.47 0.34 0.59 0.31 0.31 0.00 0.09 -0.2 -0.1 0.00
48 0.00 0.00 0.00 0.56 0.63 0.53 0.44 0.34 0.53 0.19 0.28 -0.1 0.06 -0.1 -0.1 0.00
37 0.00 0.00 0.00 0.53 0.47 0.34 0.31 0.34 0.53 0.03 0.13 -0.1 0.13 -0.0 -0.1 0.00
28 0.00 0.00 0.00 0.50 0.34 0.16 0.22 0.13 0.28 0.00 0.09 0.00 0.13 0.06 -0.1 0.00
21 0.00 0.00 0.00 0.41 0.28 0.19 0.31 0.16 0.25 0.09 0.16 0.03 0.13 0.03 -0.1 0.00
17 0.00 0.00 0.00 0.22 0.25 0.16 0.16 0.09 0.19 0.09 0.09 0.06 0.09 0.00 -0.1 0.00
13 0.00 0.00 0.00 0.09 0.13 0.09 0.06 0.00 0.13 0.03 0.09 0.06 0.03 0.00 0.00 0.00
9.7 0.00 0.00 0.00 0.09 0.06 0.03 0.06 0.00 0.13 0.03 0.03 0.03 0.03 0.00 0.00 0.00
7.5 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
5.8 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
4.6 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
3.8 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
3.1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
2.6 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
2.2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00

When I was running 2 sensors I found the offsets were all over the place too and seem to change a lot. When I went back to a single sensor due to a sensor failure I cleared them

If I ever get back to working on my Sport 1100i, are there any maps for engines that have been ported and dual-plugged?

CAJ Innovations Forums
https://cajinnovations.com/yabb0/YaBB.pl MyECU >> Maps >> Moto Guzzi 1997 Sport 1100i https://cajinnovations.com/yabb0/YaBB.pl?num=1294976319 Message started by YaBB Administrator on 01/14/11 at 14:38:39