CAJ Innovations Forums

12/10/24 at 07:34:47

	Welcome, Guest. Please Login or Register
	Welcome to our forum.

Home

Help

CAJ Innovations Forums › MyECU › MyECU Advanced usage › LC1 issues

(Moderators: YaBB Administrator, _Cliff_)

‹ Previous Topic | Next Topic ›

Pages: 1

LC1 issues (Read 4760 times)

Luke

YaBB Newbies

Offline

I love MyECU!

Posts: 4

LC1 issues
12/19/15 at 09:13:12

Hello . I have an enquiry out to Innovate but thought I'd ask here as well .
I have had an LC1 fitted to my guzzi for a couple of years but beyond first setting up have not taken a whole lot of notice of it . Thought I should re-calibrate the sensor . Question is ; has anyone here had a situation where the Led in control box plays dead ? Nothing I do gets a response . Power is there at the (box) on/off switch . Do Led's die ? It's preventing my performing calibration Sad

TIA .

IP Logged

Mad Farquhar

Full Member

Offline

Slainthe mhath

Posts: 171
Black Isle, Scotland
Gender: male

Re: LC1 issues
Reply #1 - 12/22/15 at 02:07:42

Not sure if they die other than being blown with too much power but the one on the original Marelli ecu code diagnosis strap on my 1100 Sport suffered a broken inline resistor (encased!) which had me stroking my chin for several days on and off due to the intermittent work/not work, flash/not flash until I poked about and found it sheared through the middle.
I cannot remember the Innovate software but if you connect up to a computer would it not give some form of acknowledgement of calibration? It's that long since I looked I'm probably talking equine dung.

MG Sport 1100 inj
Triking
Honda ST1100
V7 Stone

IP Logged

Luke

YaBB Newbies

Offline

I love MyECU!

Posts: 4

Re: LC1 issues
Reply #2 - 12/22/15 at 05:39:34

Hoots mon , I've got a bite !

Well I since snipped it out (LED) and put 1.2 volts through it and also tried the diode setting test on a MMeter both of which produced F A so I think it must have gone phut .
Innovate said hook the system up but it was not clear to me quite what that would yield . They did say a duff LED would not cause a total stop of the system but the part is vital to the calibration process . It's also supposed to glow all the time the bike runs.
Thanks G. Still running the Sport ?

Luke - previously known as One Centauro Wink

IP Logged

Mad Farquhar Full Member Offline Slainthe mhath Posts: 171 Black Isle, Scotland Gender:	Re: LC1 issues Reply #3 - 12/22/15 at 06:24:16 Pop down to Maplin / Radio Spares etc for a bag of assorted leds then :-0 Yup 1100 Sportie still in the stable. Merry festive - hope the calibration works. g
Back to top	« Last Edit: 12/22/15 at 06:25:17 by Mad Farquhar » MG Sport 1100 inj Triking Honda ST1100 V7 Stone IP Logged

Luke YaBB Newbies Offline I love MyECU! Posts: 4	Re: LC1 issues Reply #4 - 12/23/15 at 04:39:36 Cool , will do Gav , there is a Maplins local and I'm down there tomorrow . Aye , Crimbo greetings reciprocated
Back to top	IP Logged

Luke YaBB Newbies Offline I love MyECU! Posts: 4	Re: LC1 issues Reply #5 - 12/24/15 at 03:07:49 think that 5v might have been right V's and not 1.2 but whatever ... a new one checked out on MM diode setting )
Back to top	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

« Home

‹ Board

Top of this page