CAJ Innovations Forums - implementing my16m for mv agusta f4 1000s

10/16/24 at 02:38:56

	Welcome, Guest. Please Login or Register
	Welcome to our forum.

Home

Help

CAJ Innovations Forums › MyECU › Maps › implementing my16m for mv agusta f4 1000s

(Moderator: _Cliff_)

‹ No Topic | Next Topic ›

Pages: 1

implementing my16m for mv agusta f4 1000s (Read 136 times)

frdini

YaBB Newbies

Offline

I love MyECU!

Posts: 3

implementing my16m for mv agusta f4 1000s
09/17/24 at 02:59:48

hi Guys,
i m a newby in the field of myecu. I'm living in France and i'm riding a mv agusta f4 1000s from 2005.
I m working in information technologies.

I would like to swap the original ecu iaw16m.ar to a my16m.
I would like to discuss with people Who already did the swap on an mv agusta or other italian bikes to find help on this project.
I don't realize the difficulties that i will be facing yet.
Did anyone already build a map for my16m to replace a iaw16m.ar Roll Eyes

?
Best regards

IP Logged

Motociclo

YaBB Newbies

Offline

Hold it flat!!!

Posts: 32

Re: implementing my16m for mv agusta f4 1000s
Reply #1 - 09/17/24 at 17:54:53

Heres one that was posted some time ago. May be a start.

https://cajinnovations.com/yabb0/YaBB.pl?num=1401475562

Its not a hard process to change.
Tuning is not particularly hard if using Wide Band O2 sensor. I recommend getting one installed. Takes all the guess work out.
I was lucky enough to get a stock fuel and ignition map for my ST4. Gave me a baseline to work with.

« Last Edit: 09/17/24 at 18:02:51 by Motociclo »

IP Logged

frdini

YaBB Newbies

Offline

I love MyECU!

Posts: 3

Re: implementing my16m for mv agusta f4 1000s
Reply #2 - 09/19/24 at 05:26:40

Hello Motociclo,

Thank you for this answer.

What wide band O2 sensor do you use?

Rickf4 upload his map for a brutal which is very similar to the 1000S a few years ago. i'm thinking to start with it.

My bike is not equiped with a lambda sensor. However there is a bung pre installed on the exhaust right after the 4in1 junction. Do you think i should install a lamba sensor (Bosch 4.9 LSU) prior to go through the configuration?

catalyseur-mv-agusta-f4-1000.jpg (89 KB | 6 )

IP Logged

Motociclo

YaBB Newbies

Offline

Hold it flat!!!

Posts: 32

Re: implementing my16m for mv agusta f4 1000s
Reply #3 - 09/19/24 at 12:48:44

I use this sensor kit,

https://www.aemelectronics.com/products/dashes_and_gauges/wideband_gauges/classi...

If you wanted a kit without a gauge, there are plenty out there.
I modified the main wiring harness of this kit, harness is quite long.
But only the harness. Can't shorten the sensor wiring with out affecting calibration.

Check the thread diametre of bung, if 18mm x 1.5 thread, you could use that bung. If not, easy to get one welded in.

IP Logged

frdini YaBB Newbies Offline I love MyECU! Posts: 3	Re: implementing my16m for mv agusta f4 1000s Reply #4 - 09/22/24 at 03:00:06 Hello, i realized that the bung on the picture is designed for a CO sensor not for lambda.
Back to top	IP Logged

Pages: 1

‹ No Topic | Next Topic ›

« Home

‹ Board

Top of this page